- Lolita Skirt...Workshop

- Lolita Skirt

with a hidden zipper on one side.

 dimensions

• Length: 50 cm
• Waist: individually
• Belt width: 3 cm

You need:

1. 90 cm x 150 cm black cotton fabric
2. 100 cm x 150 cm (or 140 cm) Polkadotstoff Cotton
3. 415 cm x 0.5 cm white satin ribbon
4. approx. 2 cm wide button 
5.  fiber fabric
6. approximately 15 cm length of the zipper

Note:

I have for this version of the low edge selected.

It is about 165 cm,

instead of the usual 200 cm wide

(Not related to the hem ruffles). 

Nevertheless, sufficient hem,

necessary to give the skirt a bell shape.
Dimensions waist skirt suit 60 to 80 cm.

You can extend the upper periphery, respectively.

There typically is about twice the length of material

Instructions

1. cutting

First, cut out the pattern, as shown below: 

In the drawing only schematically, they are not in the correct ratio.
In general, a packet consists of three arcs, two front and one back.
The two rear portions depending on the pattern,

while for before the template on the edge

where the red arrow is reflected thread

again it will be launched and will be drawn.
At the top, short edge seam allowance of 2 cm

and the back seam of the two backs

(Rear seam = a red thread arrow) is 2.5 cm to.

The rest is still 1 cm seam allowance.

Figure no. 2 you can see the back of the skirt

a double folded fabric, red line marks the outline of the pattern.

Vertical edge on the right rear side seams

with a 2.5 cm seam allowance.

To be part of the front vertical line only

exactly on the spot Stoffbruch (Stoffbruch = folded axis mirror matter)

and then along the markings with a cut allowance without Stoffbruch edge

to break through.

When you open the whole, one has the original quasi

Dual side by side.

Please do not forget the way the yarn that should work

vertically through the material to be treated.

Thread parallel to the side edges of the fabric.

Ruffles for three 9.5 cm x 150 cm are cut and

Three 18 cm x 150 cm strip Polkadotstoff.

First, your own waist measurement, + 2.5 cm for the button.

More length of the belt, to which the button is sewn)

and added on both sides of the seam allowance.

Of the remaining Polkadotstoff cut a rectangle

8 cm x estimated length of 8 cm seam allowance included

Now, the following items must

be available (see picture No. 3.)

• double back skirt
•   before
• belt
• three narrow strips jabot (top ruffle)
• three broad frill strip (bottom frill)

2. Sewing

The belt and the top of the back sides of the weld interface to iron.

On the back seam on each side of the rectangle above a small

5 cm x 20 cm eliminated (br. Image Nr. 4).

 Skip the cutting edge of the upper and lower edges of the skirt

 and three lanes direct band-ruffle.

Then put two backs on the back seam

together with the right side and to lay on top of the zipper,

as seen in the picture. 5 ,.

Because when the zipper teeth, and we put a mark

sewing from the bottom up to the mark firmly

see the red line in the picture.

Do not forget that the seam allowance of 2.5 cm, there was a stitched seam

and 2.5 cm from the edge.

Sew together two backs and sew,

directly in front of the fixed.

Uzkkaya strip sewn together on the short edges

to form a ring, as well as broader frill strip.

We have two rings, one 9.5 cm and one 18 cm wide.

The edges of the wide ring then reloaded back.

If the lower edge of the offers to the material for each 1 cm

double and stitched in place.

The upper edge is folded only 2 cm

just in the opposite direction.

They are provided around the seam ruffles.
Tousled seam in contrast to the normal seam is not stitched

(= Sew the end and the beginning several times back and forth,

to fix) and the stitch length should be large and

The thread tension is weak to adjust as much as possible.
Therefore, it is possible, if the seam was quilted,

gently tighten thread

at one end while holding the other thread.

Thus, the material stretches along and get frills,

when you press the fabric handle.
It is the same on the two long sides

narrow disheveled.

In the picture we see on the part of the skirt,

that is, the side seam and shows us

the left is the back seam. 

Now narrow ruffled secure the pins on the skirt.

The length of the ruffle evenly distributed on the bottom edge.
Fig. 7 above.
On the top edge of the white satin ribbon sewn around

 Figure 7 Center.
Disheveled seam webs should lie on the edge of the skirt.

Image # 7 below ..

Also tighten the strings, distribute, sewing and connect to the seam,

the other satin ribbon ruffles uniformly.

The skirt should be as follows:

Next, insert the zipper

13.

Thus, the skirt is finished

options

• You can, of course, other ideas frills
• Create a hem length of 42 cm in length
• added to the skirt pattern.
• Only down more other size (4 cm and 18 cm).
• Then you need to make sure that the skirt anywhere
• length of 39 cm.
• The length varies by modifying 39-cm 
• Add decorative elements