OVERALL ....... Free tutorial

 

Sew yourself comfortable suit for recreation,

is a linen cloth.

materials

2.5 meters of linen
and the standard sewing thread
5 buttons

instruments

Pattern Wizard, paper pattern
paper, fabric scissors, rotary cutter
fabric marker, pins, tape measure, seam ripper
bias tape maker,

buttonhole foot, hand sewing needle

Steps

Note: Pre-wash fabric.

1. The pins, so it's easier to work with.

2. The diagram shows the pattern

US size 4-6

(England size 8-10). 

Do not forget to add a 3/8 inch (1 cm)

allowance around all panels.

 If you need help, follow  this  tutorial.

 Add 3/8 inch (1 cm) on all joints of panels,

unless otherwise specified.

3. Use a serger, or choose your own method

to protect the seams from abrasion. Make sure that you

You choose a method that does not add to the weight of the fabric.

4. Pin along the curved edge of the two pocket panels.

 Sew them together. Repeat the same for the second pocket.

5. To attach a pocket on the bodice

comply with open pocket in the side seam

bodice panel, as shown in the photo below. 

Sew along this seam. 

You will only sew bottom pocket panel on the bodice.

6. On the wrong side of the pocket and

the back of the hand to her bodice,

match cuts and attach the other side of the pocket

the opening in the back of the bodice.

7. Further, the contact with the side seam of the bodice,

all the way down to the bottom of the leg.

8. Sew the line, and be very careful,

when you reach a hole pocket,

and make sure you are not caught

the other side of the pocket. Press the seam.

9. Further, the contact feet together in panel

(Panels must be facing outwards)

.Sheyte Along the seam allowance and press Open.

10. Conclusion shoulder seams and sew together.

 Repeat steps 5-9 for the other side.

11. Turn on the half on the front side,

and place it in the other half.

12. Output from the middle of the back of the bodice

and a crotch seam, right up to the front panel

and dwell on the indication of partial buttons.

13. Stitch on the seam, and then click Open.

14. After  this  tutorial, create a 1.5 m

mandatory bias tape.

15. Firstly, the switch to connect around the armhole

Romper in the first.

16. Leave about 1.15 inches (3 cm) tail loose,

a process to attach the tape along a curvilinear

edge leave about 1.5 inches (4 cm) clearance

since the beginning of the pinning. Finally, leave about

1.15 inches (3 cm) in the tail end of the pinning as well.

17. Stitch on the pinned edge.

18. Then manually match the remaining

unattached edge and fold the tape

in the opposite direction,

They form a kind of fold lines.

19. On the side of the outside belt,

pin on this fold line.

 Staple line and press.

Trim excess fabric.

20. refolding tape on the right side and

pin on the left hem,

the top line again and press.

21. Repeat for the other armhole.

22. For the collar, again as a bonding seams armhole,

 simply attach the tape to the front of the center,

and a pin along the collar, leaving

no additional tailings.

23. Top-stitch on this tape.

24. Then, after  this  lesson, follow

partially buttons on the front of the romper.

Remember that it is women's clothing, so that 

 material incision placement

on the opposite side, as shown in the textbook

 greater than the cut strip will be placed

on the front side of the material.)

25. Follow  this tutorial  to create loops 5

laying on top of buttons, arranged the same way.

26. Finally,  sew on 5 buttons

respectively on the opposite pocket in the skirt.

27. Last but not least,

click hem pants on the wrong side

panel and the top line of this skirt.